MODELLING HEDGES AND GATES

This is tutorial for making hedges and gates.

I have constructed 3 different hedges one classed as a Medium Obstacle the other 2 low Obstacles.

HIGH HEDGES

Rural Hedges, these are hedges that are not maintain and are a bit wild and messy .

Cut a number of 3 mm MDF into lengths of 15.5 cm x 3.5 cm and 7.5 cm x 3.5 cm.

Bevel the edges using box cutters.

Image showing the edges trimmed.

Using PVA glue add some gravel and odd rocks.

Undercoated.

Dry brush the gravel and rocks with Vallejo Model colour Desert Yellow and highlight by adding Iraqui sand to the Desert Yellow.

Apply some green paint on the base.

I used Rubberized Horsehair for the hedges.
Images shows how I cut a piece of horsehair to match the length of MDF.

Images shows all the Rubberized horsehair trimmed to size and ready to be fixed onto the MDF bases.

Using a hot glue gun apply glue to one side of the Rubberized horsehair.

Note where I am applying the glue, it should be the side which exposes all the layers of Horsehair.

Once you place the hedge material on the MDF base, hold it down firm for a minute till the glue sets.

Horsehair fixed in place.

At this stage to can spread out the horsehair by using a pointed instrument and add some randomness to the top of the hedge using the scissors.

I prefer to add PVA with a brush then add the flock onto the fiber.
You can also use canned Spray Adhesive instead if you prefer.

I used Gale force 9 Meadow blend for most of my hedges but you can use any flock you wish.

Finished hedges

The hedge is higher than a 28mm figure and are classed as a Medium Obstacle.

In Chain of Command:

They block LOS unless a figure is "usually" within 2" to be seen and see thru the hedge.

A figure needs to discard its higher dice rolled to cross over the hedge.
Tracked vehicles only can cross with 2D6 with the chance of getting stuck , if doubles are rolled.

LOW HEDGES

These hedges are lower in height, up to waist height and do not block LOS, its classed as a low Obstacle and to cross this hedge you roll 2 D6 and discard the lower dice.

The MDF base is the same length and width as the Rural hedges but the Fibers are lower as seen in the image above ( up to waist height).

I like to apply the PVA glue directly onto the hedge using a old brush.

For these hedges, I used Woodlands Scenic fine earth-blend to apply on the area that the hedge meets the MDF to simulate soil.

I covered the hedge with Woodland Scenic fine turf.

Once dry I applied PVA glue to the MDF base and applied flock that matched my gaming mat.

The final step was to highlight the hedge by dry brushing the hedge only ,with Vallejo Model Colour Middlestone .

The final product with 3 distinct layers, the hedge,soil and grass.

QUICK LOW HEDGE

This hedge is also a low maintained hedge it has the same characteristics as the last hedge.
I call this hedge, the "quick low maintained hedge" because its quick and easy to make.

I thought I had discovered a new way of making hedges as I had not seen anyone on the web making hedges from a Coir door mat but after completing the hedges, I stumbling onto the "Terrain Tutor " take on hedges where he had a guide on how to make this type of hedge. ..."so there is nothing new under the sun".

Flip the Coir mat over and cut strips with box cutters.

Strips ready for next stage.

Using a can of adhesive spray, cover the whole coir surface and apply fine flock.
I recommend wearing gloves.

I used Woodland Scenic green fine turf ,adding a highlight of some lighter colour fine turf.

GATES

The gates are constructed with large matches and bamboo sticks glued together and based on a 3 mm MDF base.

Once glue is dry, undercoat.

Dry brush with Vallejo model colour Beige.

Highlight with VMC Biege mixed in with some VMC Iraqui sand.

Further highlight the fence with Vallejo model colour Middlestone with a touch of Iquai sand.

MDF base painted.

Add Rubberized horse hair on the either side of the gate and secure with PVA glue.

Once dry paint PVA glue on the MDF and rubberized horse hair and apply fine flock.

Completed gate.

The reason I have placed rubberised horsehair on either side of the gate is to help blend the gate with the different terrain features that would be placed next to the gate.